Wednesday, June 1, 2011

Engine Day 3

I was hoping to assemble the cylinders today but ran into a small roadblock. I realized this morning that I did not have the 24030 valve springs I needed to convert these -A11  0-200 cylinders to -A13 C-90 configuration. I thought I had them but all I could find were the inner and middle springs. The C-90 uses a different outer valve spring and through experience with the Trojan it will not run right with the 0-200 spring installed. I ordered the springs from Aircraft Specialties , should be here next Tuesday. With that on hold I went to work on the accessory section. First I installed the crankshaft and camshaft gears.
This sets the internal timing by the alignment of the gears. Here you can see the marks properly lined up. You can just see the timing marks just behind the safety wire.

After this I cleaned up the accessory housing and assembled the oil pump.
I then installed the rear case . I have a Skytec starter for this airplane but for now I just went with the cover plate. With those little wings I'm sure this airplane will be weight sensitive.  I painted all these parts last summer, so they were all ready to bolt on.
At the left is the starter cover plate, the two empty holes are for the mags, the tachometer drive is in the center with the generator cover plate just to the right. The hole for the oil screen is at the back right. 

After dinner I went out and installed the tappet covers, the intake spider and the oil sump and check fitted all the cylinder hold down nuts. On close inspection I was not happy with the oil pick up tube, I will look for a decent one tomorrow.


I still need to clean up and measure the cylinders  before installation.


I could have had the engine on this week if I had not screwed up on the valve springs. I still have plenty of details on the airframe and engine to complete before the springs get here.

Tuesday, May 31, 2011

Ground Hog Day

Today was a complete do over of yesterday. The scraping noise turned out to be a small aluminum burr on the camshaft thrust bearing surface on the crankcase. With that dressed out, I then had to remove all the old sealant, clean everything again and then reassemble. I am back to this point with the peace of mind of knowing it's right.

Engine assembly

I ended up taking the weekend off from the Cub, but put in a full day on Monday. I started with installing the new data plate on the crankcase. This was a slow careful process as you have to drill the 6  #51 holes for the drive screws 0.190 in depth.  With that completed I bolted up the case and checked CSI's work on the line bore. My Chinese micrometers and bore gauge measured it out to within a 0.001 of spec, but it never hurts to check. With one final cleaning the case was ready for assembly.
I then measured the crankshaft before installing the connecting rods. I had done this before but somehow lost the paper I wrote it down on. I measured the rod journals then set my dial bore gauge from the micrometer , that made it easy to to measure the rod bearing clearance.
   
No, I did not pull a Don, Superior made these bearings mechanic proof. They put the oil hole in all of them! I ended up putting in new rod bolts and nuts, I just did not like the old ones that came from Gibson Aviation. I will use those in a 65 since they only have 47 hours on them. I then installed the rods, torqued the nuts, and installed the cotter pins. The crankshaft is ready for assembly. Along in here I just started working and forgot about taking pictures. Needless to say there is a lot of work to get to this point, here is the 2-4 side ready for sealant and thread.
  The camshaft and lifters are installed and lubricated. The main bearings shells are installed along with the thrust bearings and the crankshaft nose seal. In accordance with TCM's latest SB this side gets a thin coat of Permatex 3D, just enough to hold the sealing thread. This shot shows the thrust washers and nose seal.
  The 1-3 side gets a 0.010 coat of Loctite 515, not sure about the mixed sealant but that is what they call for. I think when I did the Trojan engine 10 years ago they only called for Loctite 518, because I had to special order it and I still have it. Not sure why they changed, the Trojan has not leaked a drop in 10 years. Here's the 1-3 side.
You can see the cut off starter pinion installed at the right . In this shot you can see the camshaft thrust bearings, more on this later.
After a few hours work we end up with this!
Here it is with the through bolts and flange bolts torqued. Next comes the gears and rear case, then the cylinders. Unfortunately, at this point I noticed a unusual scraping noise when the camshaft is rotated. I decided to sleep on it and check it again in the morning.