Wednesday, September 15, 2010

Door repairs completed

Today I completed the structural repairs to the lower door. I started the day working on the fuel system, I did not want to use one of those cheap hardware store unions from the finger strainer to the valve elbow, so I ordered a AN fitting from A/C Spruce. Here are the fittings trial fitted.
This fitting looks much stronger , and can be tightened individually because it has wrenching flats. The problem is that it is slightly longer and the fuel valve shutoff lever is now out of alignment with the shutoff cable. To fix this I had to reverse the bend/joggle in the actuating arm. Here it is after bending.
  It all lines up good now and should work smooth. The fuel valve and the rear tank drain are now permanently installed.
At lunch time I went out to hunt down the springs needed to finish the door. No luck at Home Depot, nothing at Lowes, finally found em at Ace Hardware. With the new springs I was able to finish the door locking pins.
Here they are all done.
Here they are installed, everything works great.
After I do some painting of the hidden areas I will weld these two actuating rod pieces together.
All this mechanism works smooth and easy, a marked improvement from what I started with. The lower door is now ready for sand blast and paint, it will be recovered with Stits process.
I spent the remainder of the day working on the boot cowl. I fitted the firewall  cover pad and cut the holes where the controls go through. I then fitted the engine mount to measure the new bolts I will need here. With the mount on I fitted the cowl to see how things fit. It will take some work, but I think the cowl will work.
Here's a picture of it together.
I finally came up with an easy way to fix the two rows of stripped screw holes on the boot cowl. I will show you on my next update. Tomorrow is a Cub free day, I have to work on the brakes on the Trojan.
My role model says, I've been working too hard anyway.

Tuesday, September 14, 2010

Lower Door Repairs

I had all intentions of working on the boot cowl today, but just could not get excited about it . So I started on the lower door repairs. The lower door as received was a mess. The internal supports were broken and the door latch pins would not work.  Last month I fitted new internal structure and had my friend Bill weld it up. The problem came from me not jigging the assembly properly and I got some distortion. After much bending and tweaking  it still did not fit so I had to cut the forward upright to allow me to pull the front of the door down. I made an angle slice to make it easy to work and weld.
Here is where it needed to come down about a 1/4 inch, the door latching pin would not hit the hole in the fuselage frame. Cutting the upright made this easy to get right.
Here it is after welding and grinding the tube smooth.
I also made two new latch pin and spring assemblies, both the originals were in really poor shape. I had a little trouble with the brazing , all I had was solder flux and I guess that is not the proper flux. There is also a fine line between hot enough and too hot, that was difficult to control with Oxy-acetylene.
The washer on the left is brazed on, then the spring and another washer go on then the end is flattened and drilled for the actuating rod. I got the washers brazed but did not want to use the old springs, I will pick up some tomorrow.
I also brazed the door handle support, this had some old braze still existing and the new braze did not want to stick. it's not pretty but it's stuck together. Here it is before.
And after.
I could not figure out how to make the actuating rod in one piece, so you can see here the link I made at the handle arm. Due to the strut cutout in the door I made this rod and the two will over lap about 1 inch. I will weld the two together at final assembly.
Here is the door installed with the new pins . It will look a lot better after a little sandblast and paint.
I understand why everyone wants $450 for one of these doors new, there is a lot of work in this assembly.
I should finish the door tomorrow after a trip to get some new springs. I will probably sandblast and paint this while it's cool and dry. That's it for today.

Monday, September 13, 2010

Another Alcohol related tragedy

Not much progress to report this weekend, got sidetracked by other projects. Friday was spent down at Wakefield where I keep the Trojan. I've  been having some trouble with my "date" car, guess it has not been getting enough use ! Even though I keep a little 100LL in her, the fuel still went bad and I had to remove the carburetor and filter for cleaning.
The Solex 30PICT-1 carb is dirt simple and made completely of metal so you can dunk the whole thing in carb cleaner. Here it is all completed.
I let the date bike set too long also, and the Carb had to come off for cleaning. I noticed a fuel smell and found the balance line between the fuel tanks had succumb to the new alcohol fuel.   It was pretty ugly.
I had to cut the line to get the tank off the frame, but you can see how the line just fell apart.  Of course the keihin carb was all clogged up and I spent most of today going through it. For some reason they decided to make the fuel inlet fitting out of plastic? That is the only fixed plastic part so you can't put the whole body in the carb cleaner. I had to replace this crappy fitting once already. Here it is all ready to go.
You can see the plastic fuel inlet fitting.
I did get a little work done on the Cub on Saturday, I finished out the tailwheel. I took it completely apart, checked and lubricated it and got it back together and installed. A long time ago I made this cool tool to lubricate the bearings on a Maule solid tailwheel. I can't remember if I made this on the lathe or if it was just an axle I had from a larger tailwheel. Here is a picture of it.
It works great, just a couple pumps on the grease gun and your done.
Here is the overhauled tailwheel, new tail spring and bracket, installed with all new hardware.
This shot is a little blurry but you can see the new spring and bracket.
Of course Sunday was rainy and a great day to watch football and cook some grub for this week! How about those Redskins !!!!! I did take some time to order the remaining items I need to complete this weeks projects. I should be back on the boot cowl tomorrow.