Wednesday, April 11, 2012

Antenna Completed

I finished the wiring of the antenna last week and have been doing some testing. Unfortunately the spring winds have arrived and I have not done much flying. It has been an odd spring, either 70-80 degrees with a strong SW wind or 50 degrees with a strong N wind. Here is a shot of the wiring installed and the cover plate installed.





 The initial test flight was a disappointment, by moving the antenna forward I now had some ignition noise causing the radio to break squelch. The Icom A6 has a very sensitive receiver , it picks up everything wanted or not.  However after some tweaking I think this installation will be OK. First the ANL (automatic noise limiter) got turned off, with it on the ignition noise is barely noticeable. Then by increasing the squelch setting to 15 from 10 (the range is 0-24) the radio worked much better. With the lower sensitivity of the internal antenna I needed the lower squelch setting.
While not perfect this is an acceptable solution. I can now receive the ATIS at Richmond 33nm away at 1500 feet, most importantly when the airplane is pointed that way! Of course there are trade offs. There are a couple narrow blank spots where the landing gear blocks the antenna and directly aft off the tip of the rod.  I would say about 4:30, 6:00 and 7:30 positions are a little weak with fantastic airborne performance from 7:30 around to 4:30 in front of the airplane. Here is a shot of the final install.

  
I fixed one last little item that had been bothering me last week with the oil change. These inter- cylinder baffles kept blowing out of position.




I bought these from WagAero and just assumed they were correct. It seems that the mounting hole is too far outboard and the moment created by the air load allowed these to move out of position. I removed these and relocated the mounting hole 3/4 inch inboard. So far they seem to be staying in position.


With 85 hrs on the engine the oil change was due, compressions were all mid 70's, screen and magnetic drain plug were clean and everything looks clean and tight. Ready for a summer of evening patrols.

Wednesday, April 4, 2012

Antenna Issues

I have been working to optimize the communication antenna installation on the Cub. My home airport has significant transient traffic, so a good radio is a must for safe operation. I started with just the short antenna that came with the radio, however that had limited range and a tendency to feed back through the microphone wiring.  I had purchased a dipole antenna for my Taylorcraft and could never get it to work properly. It was installed in the tail behind the cockpit. I still had it so I thought I would give it a try in the Cub. Here is a link to the antenna web site.

 http://www.advancedaircraft.com/

To make a long story short, I have tried this antenna vertical, angled right , angled left, angled forward and back, side ways, and curved in every direction . In every case the reception to the sides is great but the signal is blanked directly to the front. The only place it will fit due to it's length is behind the seat in the fuselage.



The combination of tubing , pilot, passenger, engine, fuel tank, and firewall, must shield the antenna from any forward signal. You can turn 15 degrees left or right and receive a usable signal.
My test procedure is to takeoff from KJGG and climb to 1500 feet and tune the ASOS at KAKQ 20 nm away. I then execute a slow 360 degree turn while monitoring the signal. In every case the signal is blanked to the front where you need it the most. On my Taylorcraft I gave up on this antenna and installed a bent whip on the bottom of the boot cowling.
On the Cub this would be more difficult because there is no access to the inside of the boot cowling to install a proper doubler and to attach connectors. It took some brainstorming but I finally figured out a method. I decided to attach the antenna directly to the bottom of the forward floor boards, all the loads would be absorbed here. The physical antenna would protrude through a small hole in the lower boot cowl. Here is the attach bracket I came up with, it's formed from 0.040  2024-T3 aluminum.


Using a 2 inch hole saw I cut a hole in the forward floor boards.


Here is a shot of the completed mounting bracket with nut plates installed and a coat of alodine.


 
With the help of my friend Scott , we figured out a process to install the antenna , add the insulator, install the bracket, and tighten it all up. It was a slow careful process because anything you drop is a frustrating exercise in fishing to recover. If it's not magnetic you have just lost and hour.  Here are some shots installed. Once the wiring and testing are completed I will make an aluminum cover plate and remove the AN970 washers, painted black you will hardly notice it.


The safety wire is the path the antenna wire will follow under the floor boards. Here are some shots outside.




I'm not sure how this will work with the landing gear so close and the limited area for ground plane provided by the narrow boot cowl. It was an improvement on my Taylorcraft so I'm hoping for the same here. I would settle for being able to transmit and receive in the direction I am traveling. I hope to wire and test this on Friday, tomorrow is my father's 91st birthday!   

Sunday, April 1, 2012

Tailwheel issues

When I got the  Cub project the tailwheel was missing, so I rebuilt an old 1 1/4 inch Maule SFSA unit I had in stock. It was in pretty good shape but had a little wear on the main bushing, however I did not have the tooling to replace it. Lately I had been experiencing an occasional tailwheel shimmy on landing. Nothing you could not stop with a little forward pressure on the stick but annoying just the same. I thought this was due to the wear in the tailwheel so I ordered a new bushing from Aircraft Spruce and made the tools to do the job correctly. First I had to make a tool to remove the old bushing, my friends at Mid Atlantic Aviation let me use their lathe and I made this tool from some 4130 scrap.


The small end is 0.005 less than the ID of the bushing and the large end is 0.005 less than the ID of the pivot forging. Here is a shot of the new bushing.


Here is the old bushing still installed.


First you have to remove the two screws that hold the unlocking cam and the grease fitting. These extend into the bushing.


Then using the tool in a hydraulic press you can remove the worn bushing.



After cleaning up the forging , I used the tool in the press to install the new bushing.



After installing the bushing I carefully drilled through the threaded holes in the forging and through the new bushing. I then tapped the threads into the bushing. Since installing the bushing slightly reduces it's inside diameter, I reamed the ID to 0.875.


I cleaned and inspected all the other parts and reassembled the tailwheel. The old tire I had been using was worn funny so I installed a new tire.


Here is the completed tailwheel installed on the airplane, notice anything odd?


Notice the pivot axis of the tailwheel. It is actually tilted a little forward when it should be vertical or slightly aft ! This was a real boner on my part because I had installed a 1/8 inch rubber pad between the tailwheel spring and the airplane tail post , this changed the geometry of the spring and changed the pivot axis.


 I removed the pad and no more shimmy. While the tailwheel rebuild was very educational, the wear was probably not the cause of the problem after all. Here it is with the pad removed. I have decided to reinstall the pad and add a couple washers at the front attach bolt to maintain the correct angle. I think the pad does cushion the airframe a little from the tailwheel loads. Here it is all cleaned up , ready for a summer of flying.