Tuesday, May 10, 2011

Jury Struts

I'm not sure where today went, I sure don't have much to show for progress. I did manage to finish the right jury struts today. The problem with working at the airport is the visitors and the helpers. I'm going to make a sign for the hanger, "10 Minute Limit for Visitors, 5 Minute Limit for Helpers"! I guess people that have never assembled an airplane think that your doing it with your hands and that you can chat with them while you work? I can see why the local shop has a chain across the open hanger door. Oh well , back to the jury struts. The right side struts just barely hit the lower door when it opened. There is a cutout on the lower door to clear the struts due to the revised angle of the Clip wing struts. I guess I put a little too much fabric on the lower door cutout. I wanted to use the jury struts to push down the struts just slightly to provide clearance. I brought out two solid cinder blocks from home and used a ratchet strap  to pull the struts down while I installed the jury strut clamps. Worked like a charm and the door works fine now. I did not take a picture of this operation, but here is the right side finished.

Here is a shot of the struts and the cutout in the lower door.

With that completed I installed the fabric reinforcements where the aileron and rudder cables exit the wing and fuselage. I used double sided carpet tape to install these. If you use glue it seems to get everywhere and looks like crap. This might not work but I thought it was worth a try.

That was it for today. My parts order will be here tomorrow, maybe I will make some real progress.

Monday, May 9, 2011

Root Fairings

Had an appointment in the middle of the day today so that split up today's progress. I started by making the new skylight in the shade tree shop at the house. It should not crack like the first attempt. The honeysuckle is out this week and the shop smells divine !
I only got in about 3 hours at the airport today. I installed all the root fairings except the two at the front and trial fitted the skylight.
 Here's the left side bottom.
and the right side.
They still need a little clean up , but they fit good enough for a beater Cub. I worked on the front curved pieces for a while , but could not get them to fit the way I wanted. I lost interest in this so I finished the left hand jury strut installation. I did chip the powder coat in a couple places but overall it came out OK.
 

I hope to put in a full day tomorrow. BC wanted to say Hi to his Mom for mothers day.

Saturday, May 7, 2011

Cotter Pins

Last night at exactly 4:20 I came up with a brain storm on how to fix the aileron cables right. Heat shrink tubing! Since Mr. Solanberg neglected to install an inspection panel so you could access the balance cable pulley inside the wing, I was reluctant to attempt cable replacement.  My plan was to cut the nicopress off the aileron cable inside the cockpit , then join the butt ends of the old and new cable with heat shrink tubing. For added reinforcement, I wrapped the joint carefully with electrical tape, taking care not to increase the diameter too much. I  pulled the new cable through the wing and across the pulley. Worked like a charm. I then used my new old tool to install the inside nicopress, this tool is the bomb!
  This tool is really for 5 tucking but works good for this method too. The knob on the side opens and closes the jaws , the center thumb wheel adjusts the anvil clamp. It holds the cable and thimble tight while you squeeze the nicopress. Makes this a one person operation.
I also like to put a little heat shrink on the pigtail to keep it from fraying. Here's the finished product.
I then finished the end that attaches to the lower aileron horn. I added to the cable length so that no threads were showing on the turnbuckles.
And I did not have to install a funky spacer in the middle where everyone could see it.
The rest of the afternoon was spent installing a thousand cotter pins in all the joints in the aileron control system. All I have remaining here is to safety the turnbuckles. I will probably do this with 0.032 single wrap until I have it rigged just the way I want it. Since it was Saturday I had a lot of visitors(and advice) so this is all I got accomplished.