Wednesday, April 20, 2011

Got Tail ?

Since my hanger faces NNE, and the sun is brutal in the morning, I decided to go out after lunch today. I started by cleaning and lubricating all the trim mechanism components. It's my understanding that this is a problem area on the clipwings because of increased loading. Everything got cleaned and fresh grease, the stabilizer leading and trailing edge tubes got some Boeshield , then the stabilizers were installed.  I then installed the bracing wires and did an initial rigging on the stabilizer. The elevators were then installed and the controls hooked up. Of course I forgot to bring out the manual and my cable tension tool so I did not get it all finished. Here are a few shots.
There is all new hardware installed in the control circuit.
The Univair stainless tail brace wires are really sweet and worth every penny.
I need to sit down and go over this with the parts manual in hand, this was all wrong when I bought the project. When it looks right , I just need a few cotter pins and safety the turnbuckles and she's ready to button up. I will probably take tomorrow off, check back Friday for more progress.

Tuesday, April 19, 2011

Early morning

Got up today at the crack of dawn for the trip to the airport. Everything went smooth and only saw one cop,  he must have been dreaming of donuts because he never even looked. I dropped the fuselage in front of the hanger and headed home for breakfast and morning chores. Here she is at the hanger.
Here is a shot of the 4 point towing setup. Two ratchet straps go aft and two froward. They all attach to the tailwheel fork that way the fuselage can pivot in turns. The two slack straps going forward are just safety straps. You have to be careful to tie far enough aft in the bed so that the sharpest turn does not hit the side of the bed. Tows great like this.
I spent the morning working to get the garage ready for engine assembly. After lunch I loaded up the tail feathers and went out to work on hanger. The goal for the afternoon was to make room for the fuselage. It only took about 3 hrs work and 2 hours of bullshitting with airport bums to get er done. I think there might actually be infinite space in a T hanger because no matter how I try I can't seem to fill this one! It will still take some work to make room for wing assembly and to get the tail in the right way.
Lucky for me the airport manager has a fork lift to move this.
The bridgeport and the loose fabric on the Commonwealth are all that's holding up wing assembly.  She sure looks good in the hanger. The fuselage went home August 29, 2010, not sure why it took 8 months but were getting there SLOW but sure.

Tomorrow morning the tail goes on for final assembly. Check back for pictures. I think I'll try to take BC out to the hanger one day to see if he likes it, lots of stuff to sniff in there. He's really not crazy about riding in the car.

Monday, April 18, 2011

It's time

It's time for the fuselage to go back to the airport. I can't work on the skylight because the garage roof is too low and I need to finish the wing root fairings so the wings need to be installed. Today I started by completing the eyebrows, I squeezed the 3/32 rivets but had to drive the 1/8's that hold the tabs. They came out nice.
A little touch up on the black paint and they will be ready to go. With the epoxy dry on the cowl repairs, I removed all the clamps and finished a few details on the lower cowl. I fitted the cabin/carb heat inlet duct.
Everything fits good here, I then installed the mounting pins I painted yesterday.
I'm pretty happy with how this turned out, there are a lot of repairs but they should not be too noticeable from the outside after painting. Here's a couple shots.
I spent the rest of the afternoon making a bracket to replace the left front cowl pin. I did not realize it at first but there is a substantial difference between the 85/90 case and the 65 case at the front tie bolts. This means that the brand new Univair fitting I bought will not fit. I decided to make my own fitting which required cutting and grinding some 4130. I got all the pieces made today but will wait until the flight engine is on to complete it. Here's a shot, it has to bend the other direction.
  The rest of the day was spent moving crap out of the way so I could get the fuselage out of the garage. I managed to get it all hooked up to the truck just before dark and will leave for the airport first thing in the morning. I used the same 4 point tie to the tailwheel fork I used to bring it home. Here's BC giving the rig a once over.
That's it for today, the engine stand will come home tomorrow and assembly will start on the engine. I will probably spend the rest of the week cleaning the hanger and the garage.