I have always wanted a travel cover for the Trojan. The sliding canopy leaks a little when it rains and with all that plexiglass the sun really bakes the cockpit when it is all closed up. Last summer it got so hot that it fried the display on my Garmin GPS mounted on the dash. I tried to get Bruce's custom covers to make me one but they would not do it without the plane for fitting and measuring. I talked to a local guy , but the price was a little too high. Then , one day while surfing I found Kennon Covers and shot them an Email with some pictures. They came right back and said no problem. They do a lot of military work where they don't have access to the machine. They model the whole thing in CAD and make from that. So , I sent them some detailed dimensions and lots of pictures and they made a pattern out of some cheaper material for a trial fitting.
With this trial fitting we measured for the straps. It is not an optimal configuration for the hold down straps because of the cowl side vents don't let the strap pull forward. I went with the simple hole for the antennas instead of the velcro slit we originally planned. With the antennas so close together a "sock" probably would not work very good. Here is the final product, it has a little slack at the front around the windshield that I think could be improved, but overall it came out OK. It's been through some pretty good spring wind and seems to stay in place. It is supposed to rain this week so I will see how the antenna hole works, little worried about the water getting under the cover.
Overall I think it came out pretty good considering they never saw the airplane! Should keep that S&F dirt out!
Monday, March 14, 2011
Sunday, March 13, 2011
Stay of Execution
In January the governor of Virginia issued a one year stay of execution for the OLD-smobile.
The olds had developed a nasty banging in the transmission so I had decided to take her to the junk yard if it did not pass inspection . With the fresh inspection , I decided to take it to Aamco for an estimate for transmission repairs. Of course it needed a complete overhaul @ $2200 so that was not an option, they also said it had an engine miss ? Having never owned a V6 powered car, what I had thought was the transmission banging was actually the engine missing under load. It only acted up when in overdrive and under load like when you start up a hill on the interstate. I assumed it was the transmission because it ran fine otherwise.
I decided to invest $60 in new plugs and wires. Even with unleaded gas 114,000 miles is about all you get from a set of plugs ! The real culprit was a corroded terminal on one ignition coil. Here are a few shots that tell the story, check out the gap on those plugs.
Here is the corroded terminal on the #6 coil wire. Pretty ugly !
Check out #3 for comparison !
This completely eliminated the banging under load and it runs fantastic . The transmission still has the pump noise going on , but I plan on just driving it until it quits or won't pass inspection.
The olds had developed a nasty banging in the transmission so I had decided to take her to the junk yard if it did not pass inspection . With the fresh inspection , I decided to take it to Aamco for an estimate for transmission repairs. Of course it needed a complete overhaul @ $2200 so that was not an option, they also said it had an engine miss ? Having never owned a V6 powered car, what I had thought was the transmission banging was actually the engine missing under load. It only acted up when in overdrive and under load like when you start up a hill on the interstate. I assumed it was the transmission because it ran fine otherwise.
I decided to invest $60 in new plugs and wires. Even with unleaded gas 114,000 miles is about all you get from a set of plugs ! The real culprit was a corroded terminal on one ignition coil. Here are a few shots that tell the story, check out the gap on those plugs.
Here is the corroded terminal on the #6 coil wire. Pretty ugly !
Check out #3 for comparison !
This completely eliminated the banging under load and it runs fantastic . The transmission still has the pump noise going on , but I plan on just driving it until it quits or won't pass inspection.
Saturday, March 12, 2011
Slow progress
Well the cold months really slowed progress on the Clipwing. Thank goodness spring is here in Eastern Virginia. I have completed a few items on the Cub. I finally completed the panel installation with all the required placards and markings. The rear seat solo and the fuel drain placard came from Wagaero . The Clip Wing placard required by the STC I had made at the local engraving shop, it came out really nice. I ended up putting the data plate on the panel, it should be on the inside of the baggage door but I don't have one. Here are a couple shots of the completed panel.
Here are a few detail shots.
I think the panel came out pretty nice, here is a shot of the pitot installation and my own design static system. It took some work to fit the two tubes up the windshield channel, but I managed to get it to fit.
I took the easy way out on the static line to the altimeter and just used flex hose and tie wraps. It will still be better than just venting into the cabin as original.
I also completed the inside windshield trim , like I said before it was a tight fit with the pitot and static lines and the mag wires. The covers I made fit really nice, you can just see the two 1/8 aluminum lines and the wires at the top of this photo.
In this photo you can see the pitot lines and the installation of the mag switch and wires. I bought the shielding can for the A7 switch from a guy on Ebay. I had to mod it a little for the Cub installation because the wires came out the back and would hit on the wing compression tube. The back of the A7 switch is just phenolic and "leaks" radio noise that my Icom picks up constantly. Hopefully this will solve that problem.
Here is a shot of the mag switch inside.
I also installed the seat belts for the front and rear seats and completed the right side window installation. The right window has been modified in this airplane and is really pretty heavy. I was talking to Buzz about it and he says his window will flex in flight and vibrate when operating with it open. Here it is all finished.
I used those little closed end nuts instead of lock nuts to cover the screw threads on the inside. I may have to put a little lock tight on these because they are not real tight so they won't crack the plexiglass.
I'm working on the cowl this week, and will finish it before the fuselage goes to the airport. With the warmer weather I have been working a little each day on cleaning up the hanger so she will fit in for assembly. Thankfully the airport owner has a fork lift to move this!
The exhaust system is back at Dawley for the third time, hopefully this time I will finally get it right. I think my helper might have put the jinx on it.
Here are a few detail shots.
I think the panel came out pretty nice, here is a shot of the pitot installation and my own design static system. It took some work to fit the two tubes up the windshield channel, but I managed to get it to fit.
I took the easy way out on the static line to the altimeter and just used flex hose and tie wraps. It will still be better than just venting into the cabin as original.
I also completed the inside windshield trim , like I said before it was a tight fit with the pitot and static lines and the mag wires. The covers I made fit really nice, you can just see the two 1/8 aluminum lines and the wires at the top of this photo.
In this photo you can see the pitot lines and the installation of the mag switch and wires. I bought the shielding can for the A7 switch from a guy on Ebay. I had to mod it a little for the Cub installation because the wires came out the back and would hit on the wing compression tube. The back of the A7 switch is just phenolic and "leaks" radio noise that my Icom picks up constantly. Hopefully this will solve that problem.
Here is a shot of the mag switch inside.
I also installed the seat belts for the front and rear seats and completed the right side window installation. The right window has been modified in this airplane and is really pretty heavy. I was talking to Buzz about it and he says his window will flex in flight and vibrate when operating with it open. Here it is all finished.
I used those little closed end nuts instead of lock nuts to cover the screw threads on the inside. I may have to put a little lock tight on these because they are not real tight so they won't crack the plexiglass.
I'm working on the cowl this week, and will finish it before the fuselage goes to the airport. With the warmer weather I have been working a little each day on cleaning up the hanger so she will fit in for assembly. Thankfully the airport owner has a fork lift to move this!
The exhaust system is back at Dawley for the third time, hopefully this time I will finally get it right. I think my helper might have put the jinx on it.
Subscribe to:
Posts (Atom)























