Wow, progress has really slowed. With the holidays and some home projects, I'm only getting a couple hours a day on the Cub. Today I finished the right side of the panel and the fuel system. Yesterday I finished making the hoses for the fuel system. I had some problems initially , I think just because the hose was so cold. I could not get the fittings to go on without the tool slipping right near the end . I finally took the hose in the house and heated it in the oven at 100 degrees and everything went smooth. The fuel has been on for a couple days now with no leaks noted. Here is a shot under the tank.
Here is a shot under the panel showing the installation of the primer, oil temperature and oil pressure lines. It is a real back breaker working up under here, so I took special care to hopefully make this maintenance free for years.
Here is a shot on the engine side of the firewall, I will probably seal all the holes with fireproof putty after everything is complete.
And here is the gascolator and the fuel line to the carburetor.
Last but not least, we have the right side of the panel with the gauges installed for an extended trial fitting.
I'm still looking for the "solo rear seat only " placard, not sure there was one with the project. It goes where the two small holes are at the lower right. I will install a slip / skid ball after the airplane is assembled and leveled. The temp is supposed to moderate this week, so I may get the panel finished and start on the cowl.
Monday, December 20, 2010
Thursday, December 16, 2010
The Bristol Type C
We will be off the Cub project for today. There was a request for information on the Foxboro airspeed indicator on the Waco Club forum. I think I have a Foxboro, but could not find it today. I did locate my Bristol Type C airspeed indicator which I think was the predecessor of the Foxboro Company . I think they are identical in design and construction, however I could be wrong. Here is a picture of the Bristol.
As you can see it is a beautiful flange mounted Airspeed indicator with a 4 inch glass face. The radium on the 30,60, 90 , 120, 150 has long since lost it's "glow". Where it chips off it leaves a nice gold finish underneath. The question was about the glass face. Since this instrument came to me without the glass I can only estimate the original configuration. The aluminum bezel ring unscrews in a conventional manner. Using the paint witness mark on the main case , I estimate the thickness of the glass and any gasket between the bezel and glass at 0.125 inches. The diameter of the glass should be 4.000 inches.
I believe that this early airspeed operates differently than what we know today. The back is marked just like airspeed instruments are marked today.
However, the "S" stands for suction and not static as is the case today. I have read that at the time this was made, thin metal bellows technology had not evolved to the point where they could get enough deflection with pitot pressure alone. A combination pitot/venturi sensor was used to provide the necessary pressure differential. Here is a picture of a set that was for sale on Ebay a while back. Of course it went rich.
When you examine the instrument you can see that it operates opposite to what we know today. In this picture you can see that the pitot pressure fills the instrument case and effects the outside of the operating bellows. The suction pressure is applied to the inside of the bellows and the resulting differential operates the indicator needle. This shot shows the internal plumbing.
You can see that the "P" side simply vents into the case, while the "S" side has the small copper tube that I assume vents to the bellows. This design makes the sealing of the case very important and there is and "O" ring seal on the front edge.
I measure this O ring at 3.975 OD and 3.760 ID. that would make it about 0.125 diameter. Remember this one is 90 years old so measure your case and get an o ring to fit. Tom I hope this answers your questions, let me know what you find out on the glass, I need one too. Check your instrument before ordering, as this picture shows the type E Foxboro has a slightly different bezel configuration.
As you can see it is a beautiful flange mounted Airspeed indicator with a 4 inch glass face. The radium on the 30,60, 90 , 120, 150 has long since lost it's "glow". Where it chips off it leaves a nice gold finish underneath. The question was about the glass face. Since this instrument came to me without the glass I can only estimate the original configuration. The aluminum bezel ring unscrews in a conventional manner. Using the paint witness mark on the main case , I estimate the thickness of the glass and any gasket between the bezel and glass at 0.125 inches. The diameter of the glass should be 4.000 inches.
I believe that this early airspeed operates differently than what we know today. The back is marked just like airspeed instruments are marked today.
However, the "S" stands for suction and not static as is the case today. I have read that at the time this was made, thin metal bellows technology had not evolved to the point where they could get enough deflection with pitot pressure alone. A combination pitot/venturi sensor was used to provide the necessary pressure differential. Here is a picture of a set that was for sale on Ebay a while back. Of course it went rich.
When you examine the instrument you can see that it operates opposite to what we know today. In this picture you can see that the pitot pressure fills the instrument case and effects the outside of the operating bellows. The suction pressure is applied to the inside of the bellows and the resulting differential operates the indicator needle. This shot shows the internal plumbing.
You can see that the "P" side simply vents into the case, while the "S" side has the small copper tube that I assume vents to the bellows. This design makes the sealing of the case very important and there is and "O" ring seal on the front edge.
I measure this O ring at 3.975 OD and 3.760 ID. that would make it about 0.125 diameter. Remember this one is 90 years old so measure your case and get an o ring to fit. Tom I hope this answers your questions, let me know what you find out on the glass, I need one too. Check your instrument before ordering, as this picture shows the type E Foxboro has a slightly different bezel configuration.
Wednesday, December 15, 2010
Engine Details
Just a little update since I have not posted in a while. It got really cold here and my progress has been slowed considerably. I have been working on the engine installation and finishing the instrument panel. I started by fitting the exhaust system and measuring it before I send it off to Dawley for rework/modification. Piper never made a exhaust system for the -12 engine installed in a stock J3, so every one is custom made. This is the problem area,
The oil screen housing on the -12 engine is on the right side and much lower than on the -8 series engines. After removing the muffler shroud I was able to install the screen housing and get some accurate measurements. I calculated that for my airplane the muffler needs to be 1 inch lower.
After documenting all this I sent the two stacks off on Monday, they say they are swamped right now so it's hard to say when they will come back. I hope they can reuse the stamped collectors, otherwise they will make new ones from round pipe. On the left side they just change the angle of the long pipe.
On the right side , they change the angle and increase the length of the two riser pipes.
It will all look as nice as the muffler when I get them back. They did the muffler last year. I then completed the installation of the oil pressure gauge. I got the new flex line from Univair ($85 !!!) it has the restrictor fitting built in and the original auto type fitting on the other end. Per original I used 1/4 inch copper tubing , I sleeved it with vinyl tubing to protect it from chafing. Here is the final install,
Here is a shot of the inside, I still need to run the primer "out" line and this side will be finished.
Today I worked on the tach cable, cabin heat, and throttle.
To avoid sharp bends the tachometer cable curves up over the mount then back into the rear case. The throttle exits the firewall next to the tach cable, and the cabin heat comes through the upper hole. I sleeved the cabin heat cable with vinyl tubing because I have the old style heat box and it tends to chafe inside the cowling. This shot shows the control attachment at the heat box.
The throttle will have to wait until I get a chance to paint the special mounting clamp, and the return of the exhaust pipes. I did run into a little problem with my fuel drain system. If you remember I ran the drain line all the way back to the rear corner of the boot cowling. The problem was that when the drain was released the vacuum created would not let the remaining fuel drain from the line. I solved this by incorporating a vent in the drain line, it works great now.
I have been told that this is the case even without the extended drain tube.That's it for visible progress, hopefully after the snow/freezing rain tomorrow we will get back to seasonable temperatures next week.
The oil screen housing on the -12 engine is on the right side and much lower than on the -8 series engines. After removing the muffler shroud I was able to install the screen housing and get some accurate measurements. I calculated that for my airplane the muffler needs to be 1 inch lower.
After documenting all this I sent the two stacks off on Monday, they say they are swamped right now so it's hard to say when they will come back. I hope they can reuse the stamped collectors, otherwise they will make new ones from round pipe. On the left side they just change the angle of the long pipe.
On the right side , they change the angle and increase the length of the two riser pipes.
It will all look as nice as the muffler when I get them back. They did the muffler last year. I then completed the installation of the oil pressure gauge. I got the new flex line from Univair ($85 !!!) it has the restrictor fitting built in and the original auto type fitting on the other end. Per original I used 1/4 inch copper tubing , I sleeved it with vinyl tubing to protect it from chafing. Here is the final install,
Here is a shot of the inside, I still need to run the primer "out" line and this side will be finished.
Today I worked on the tach cable, cabin heat, and throttle.
To avoid sharp bends the tachometer cable curves up over the mount then back into the rear case. The throttle exits the firewall next to the tach cable, and the cabin heat comes through the upper hole. I sleeved the cabin heat cable with vinyl tubing because I have the old style heat box and it tends to chafe inside the cowling. This shot shows the control attachment at the heat box.
The throttle will have to wait until I get a chance to paint the special mounting clamp, and the return of the exhaust pipes. I did run into a little problem with my fuel drain system. If you remember I ran the drain line all the way back to the rear corner of the boot cowling. The problem was that when the drain was released the vacuum created would not let the remaining fuel drain from the line. I solved this by incorporating a vent in the drain line, it works great now.
I have been told that this is the case even without the extended drain tube.That's it for visible progress, hopefully after the snow/freezing rain tomorrow we will get back to seasonable temperatures next week.
Subscribe to:
Posts (Atom)




















