Been a while since I posted, had a lot of distractions this week. One of my outdoor cats disappeared for a few days so I had to put out an Amber alert . He showed up this morning, but is limping a little and won't let me get hold of him. I'll give it a few days and if he gets worse , I will have to trap him. Here is a shot of him, his name is Mr. Chicopee.
Been making some progress on the Cub, it has been really cold with highs only in the 30's so my work time has been limited to daylight hours. When it's dark and cold , I just don't feel like working. I have been plumbing the instruments and finishing the panel. I have a bunch of fittings and parts on order for Friday delivery. I should be able to finish the panel this weekend. Here is a shot of the final installation.
The "g" meter has glare on it from the flash. The primer , oil pressure and temperature still need a little detail work on the plumbing. The tank now has 2 gal of 100 LL in it and is leak free so far. Still need to run the pitot and static lines, the material will be here tomorrow. The screws to complete the windshield install will also be here tomorrow. I really needed to install the mockup engine so I could run all the fluid lines and controls, so I did that today. I got my engine hoist from the airport and it went on really easy. This allowed me to finish the oil temperature, primer fuel inlet line, and oil pressure line. I still have to fit the primer fuel outlet line.
I also fitted the exhaust pipes to determine the drop necessary to clear the oil screen housing. With these measurements I will send both stacks off to Dawley for rebuild and modification. The muffler and tail pipe have already been rebuilt. The only original part they will use will be the formed double stack collector. I will measure again tomorrow, but it looks to me that the muffler needs to drop 1 inch.
I'm not sure how long this will take with the holidays coming. I will send them off tomorrow. I also fitted up the cowling. I was going to order a new cowl from Univair, but I think I can rebuild an acceptable one from the parts that I have.Since I want to install the F&M oil filter it would be a shame to cut up a brand new cowl.
You can see the filter housing in the picture above, it requires a hole to be cut in the side of the top cowl. The white filter sticking through looks like crap on a yellow Cub but I don't think it will be that noticeable on my white airplane. Here is the cowl installed, I will replace the fiberglass nose bowl with a rebuilt metal one.
It will take some sheet metal work but I think I can make this work OK. I also did some work on the wing root fairing, but I did not take any pictures. They will have to wait for the wings to be installed to be fitted . That's it for this week, I had hoped for more progress but the cold has slowed me down.
Thursday, December 9, 2010
Sunday, December 5, 2010
Windshield completed
Not a whole lot of progress this weekend, however I try to do something everyday. On Saturday it was clear and sunny but cold, so I disassembled the windshield and spent a couple hours grinding , filing, sanding, and polishing all the edges. Hopefully this will keep it from cracking in service. With my coveralls on I could do this outside and that kept the mess out of the shop. Saturday evening we had our regular airport Christmas party. On Sunday morning I woke up to this scene.
The perfect Virginia snow, gone by noon! I got a late start, but I finally installed the windshield for an extended trial fitting. Before I installed the small triangular left side window I installed a vista vent from Aircraft Spruce. I tested on the scrap piece of plexiglass and found the 2 1/2 inch hole saw melted the material and made an ugly hole, so I ended up using my small fly-cutter. I installed this at the top of the window because when you sit in the back, it would be in your line of sight when landing at the bottom. It really looks much better than the cheap snap vents.
I did run out of 1/2 inch #6 screws, so I will have to replace some too short screws, but it is in!
The perfect Virginia snow, gone by noon! I got a late start, but I finally installed the windshield for an extended trial fitting. Before I installed the small triangular left side window I installed a vista vent from Aircraft Spruce. I tested on the scrap piece of plexiglass and found the 2 1/2 inch hole saw melted the material and made an ugly hole, so I ended up using my small fly-cutter. I installed this at the top of the window because when you sit in the back, it would be in your line of sight when landing at the bottom. It really looks much better than the cheap snap vents.
I did run out of 1/2 inch #6 screws, so I will have to replace some too short screws, but it is in!
I plan to replace this piece of fairing, the holes are really ugly. I will install nut plates for the wing root fairing screws. Tomorrow I plan to work on the skylight and that will finish the windows.
While I was working on the windshield I got a brainstorm on how to fix my static system problem. I wanted to install a static system to eliminate the airspeed/altitude change with window/door position. The problem is the sensitive altimeter is longer than the original and a regular AN fitting would hit the back of the fuel tank. I decided to use a standard brass cored pipe plug and make my own fitting. I used my drill press to drill one of the wrench flats #12 almost all the way through. I soldered in a length of 3/16 copper tubing, then drilled the center through with a #40 drill. Here are a couple pictures of the end product.
Here it is installed, fits great and has adequate clearance with the fuel tank.
Sometime this week I should install the fit up engine. Check back in, were making progress.
Saturday, December 4, 2010
More windshield
Started out this morning finishing the interior covers. I wanted to use the existing screw holes in the fuselage structure and that always takes more time. Using a few tricks and a lot of luck these came out looking respectable. Here is a shot of the aft cover.
Here is the front cover, they are finished except for a little smoothing and paint.
I then worked on the two windshield attachment post channels I made yesterday. I had to drill new screw holes for these because the old ones were stripped. This would have been impossible with the windshield installed. Here is the right one installed.
Here is the left one , it is cut out at the top and bottom for the pitot lines and mag switch wires. I'm still not sure how you get the screws in with the windshield installed.
I hoped to get the windshield installed today, but that did not work out. The little triangular window on the left side kinda kicked my butt. There is a lot going on at this left post where the windows overlap and three trim strips meet. I had to make some value judgments and I think I made the best decision. Here is the spot that took so long to sort out.
The three trim strips, the boot cowl, the windshield and the side window all meet here. I've looked at a lot of Cubs and every one is a little different at this spot. Here is what I ended up with, it will look better over time as the screw pressure bends the plexiglass to shape.
I plan to install a "vista" vent in this little window, people say it is hot in the front seat with the overhead skylight. I also fitted up the right side and the door fits good. Tomorrow I will remove all this and do some final polishing of the edges on the windshield then put it back together with some foam sealing tape.
That was it for progress today. My helper pussed out on me, said it was too cold!
Here is the front cover, they are finished except for a little smoothing and paint.
I then worked on the two windshield attachment post channels I made yesterday. I had to drill new screw holes for these because the old ones were stripped. This would have been impossible with the windshield installed. Here is the right one installed.
Here is the left one , it is cut out at the top and bottom for the pitot lines and mag switch wires. I'm still not sure how you get the screws in with the windshield installed.
I hoped to get the windshield installed today, but that did not work out. The little triangular window on the left side kinda kicked my butt. There is a lot going on at this left post where the windows overlap and three trim strips meet. I had to make some value judgments and I think I made the best decision. Here is the spot that took so long to sort out.
The three trim strips, the boot cowl, the windshield and the side window all meet here. I've looked at a lot of Cubs and every one is a little different at this spot. Here is what I ended up with, it will look better over time as the screw pressure bends the plexiglass to shape.
I plan to install a "vista" vent in this little window, people say it is hot in the front seat with the overhead skylight. I also fitted up the right side and the door fits good. Tomorrow I will remove all this and do some final polishing of the edges on the windshield then put it back together with some foam sealing tape.
That was it for progress today. My helper pussed out on me, said it was too cold!
Subscribe to:
Posts (Atom)





















